skillox.blogg.se

1. NETGEAR WNDA3100 INSTALLATION INSTALL
2. NETGEAR WNDA3100 INSTALLATION DRIVERS
3. NETGEAR WNDA3100 INSTALLATION UPDATE
4. NETGEAR WNDA3100 INSTALLATION DRIVER

NETGEAR WNDA3100 INSTALLATION DRIVER

You have compiled the driver for your current kernel version only. Of course, you can avoid this by not plugging or unplugging the device unless the computer is shut off. Plugging the dongle back in, you may need to restart the manager: Hot-unplugging may cause the network manager to segfault. Still several issues that need to be addressed.

NETGEAR WNDA3100 INSTALLATION UPDATE

Please get a temporary internet connection by ethernet, tethered or whatever means possible, open a terminal and do: sudo apt-get update please reconnect it!Īr9170usb: probe of 1-1:1.0 failed with error -110Īny help with starting my investigations/debugging greatly appreciated.If you ran the command lsusb and find that your device is 0846:9053, then your device is driven by a very new driver, mt7662u_sta. Usb 1-1: firmware part 1 upload failed (-110). Modules linked in: ar9170usb(+) mac80211 cfg80211 fuse sco bridge stp llc bnep l2cap bluetooth sunrpc ipv6 vmblock vsock vmci vmxnet vmmemctl vmhgfs pvscsi dm_multipath uinput snd_ens1371 gameport snd_rawmidi snd_seq_device snd_ac97_codec ac97_bus snd_pcm snd_timer snd pcnet32 soundcore snd_page_alloc ppdev i2c_piix4 mii parport_pc i2c_core parport pcspkr floppy mptspi mptscsih mptbase scsi_transport_spi Usb 1-1: firmware: requesting ar9170-2.fwīUG: soft lockup - CPU#0 stuck for 61s! Usb 1-1: file with init values not found.Īr9170usb: probe of 1-1:1.0 failed with error -2 Usb 1-1: firmware: requesting ar9170-1.fw Usb 1-1: reset high speed USB device using ehci_hcd and address 4 (start_freq - end_freq bandwidth), (max_antenna_gain, max_eirp) Usb 1-1: configuration #1 chosen from 1 choiceĬfg80211: Calling CRDA to update world regulatory domainĬfg80211: World regulatory domain updated: Usb 1-1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 Usb 1-1: New USB device found, idVendor=0846, idProduct=9010 Usb 1-1: new high speed USB device using ehci_hcd and address 4 Usbcore: deregistering interface driver ar9170usb

Usbcore: registered new interface driver ar9170usb

NETGEAR WNDA3100 INSTALLATION INSTALL

Here is the output from dmesg on the guest FC11 install on the W7 64-bit host: I have downloaded and built the latest kernel wireless drivers, but the end result is exactly the same on the W7 64-bit host - long freeze followed by failure.

NETGEAR WNDA3100 INSTALLATION DRIVERS

Where do I start to debug this? What log files or debugging options are available in VMWare to help work through this problem? I'll also be playing around with the FC11 drivers to try and work out why the device is freezing (/not downloading the firmware), but I need some pointers for the host side of debugging. This would tend to suggest that the Windows 7 host, OR the hardware on the Windows 7 host (or possibly some 64-bit issue) is causing issues. I went back to the original host (32-bit XP pro) and installed the WNDA3100 adapter in the same FC11 guest, and it works fine. This eventually times out and I get all sorts of kernel tracebacks and other nastiness. I then tried to install the WNDA3100 adapter in the FC11 guest on the W7 host, but get freezes of up to 60 seconds (as the firmware is downloaded onto the WNDA3100 card). The guest FC11 install still works fine (had to tweak the networking a little, but all is good now). I then transferred this VM across to the Windows 7 Pro 64-bit host. Situation is that I have a single VM, created under XP pro, 32-bit, guest is fedora core 11. Long winded problem, unsure where to start debugging.